收藏本站
MAX8930
WLED Charge Pump, RGB, OLED Boost,
LDOs with ALC and CAI
Inductor Selection
Smaller inductance values typically offer smaller physi-
cal size for a given series resistance or saturation cur-
rent. The inductor’s saturation current rating should be
greater than the peak switching current. Recommended
inductor values range from 10 F H to 100 F H (e.g., 22 F H,
VLF3010AT-220MR33-1, TDK).
Capacitor Selection
Small, ceramic surface-mount capacitors with X7R or
X5R temperature characteristics are recommended due
to their small size, low cost, low equivalent series resis-
tance (ESR), and low equivalent series inductance (ESL).
If nonceramic capacitors are used, it is important that
they have low ESR to reduce the output ripple voltage
and peak-to-peak load transient voltage.
this function is used in conjunction with a microproces-
sor ( F P), connect a pullup resistor between CHG and
the logic I/O voltage to indicate charge status to the F P.
I 2 C Interface
The slave address for MAX8930 is EC/Dh in write/read
mode.
SDA
SCL
CHG Charge-Indicator Output
CHG is an open-drain output that indicates charger sta-
tus and can be used with an LED. CHG goes low during
DATA LINE STABLE
DATA VALID
CHANGE OF
DATA ALLOWED
charging when the bit of CHG at 02h is 1. CHG goes
high impedance when the bit of CHG at 02h is 0. When
Table 8. Recommended Inductors
Figure 10. SDA and SCL Bit Transfer
DESIGNATION
L SW
VALUE (μH)
22
22
22
22
47
68
DCR ( I )
1.5
4.0
1.0
5.0
2.2
3.3
MANUFACTURER
TDK
Panasonic
Taiyo Yuden
Taiyo Yuden
Sumida
Taiyo Yuden
PART
VLF3010AT-220MR33-1
ELJPC220KF
LB2016-220
LEM2520-220
CMD4D11-47
LEMC3225-680
CURRENT (mA)
330
160
105
125
180
120
Table 9. Recommended Capacitors
DESIGNATION
C PV5
C OUT
VALUE (μF)
1
1
MANUFACTURER
TDK
Taiyo Yuden
PART
C2012X5R0J105M
TMK316BJ105KL
DESCRIPTION
1 F F Q 20%, 6.3V X5R ceramic capacitor
1 F F Q 20%, 25V X7R ceramic capacitor
Table 10. Slave Address
A7
1
A6
1
A5
1
A4
0
A3
1
A2
1
A1
0
R/W
1/0
32
Maxim Integrated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAXQ2000-KIT EVAL KIT FOR MAXQ2000
MAXQ610-KIT# EVALUATION KIT FOR MAXQ610
MB2146-401-01A KIT STARTER F2MC-8FX 3V
MB2146-401-03A KIT STARTER F2MC-8FX 5V
MB2146-410A-01-E KIT STARTER MB95200/210H SERIES
MB85R1001ANC-GE1 IC FRAM 1MBIT 150NS 48TSOP
MB85R1002ANC-GE1 IC FRAM 1MBIT 150NS 48TSOP
MB85R256FPFCN-G-BNDE1 IC FRAM 256KBIT 150NS 28TSOP
相关代理商/技术参数
MAX8931EVKIT+ 制造商:Maxim Integrated Products 功能描述:5V RS232 TRANSCEIVER - Boxed Product (Development Kits)
MAX8932EVKIT+ 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX8932EWT120+T 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX8934AETI+ 功能描述:电池管理 Dual Linear Charger Smart Power Selector RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX8934AETI+T 功能描述:电池管理 Dual Linear Charger Smart Power Selector RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX8934BETI+ 功能描述:电池管理 Dual Linear Charger Smart Power Selector RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX8934BETI+ 制造商:Maxim Integrated Products 功能描述:IC BATTERY CHARGER DUAL 28TQFN
MAX8934BETI+T 功能描述:电池管理 Dual Linear Charger Smart Power Selector RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel